2W 5.8GHz 48CH FPV VTX Video Transmitter w/ 0mW/200mW/500mW/1000mW/2000mW + Antenna for Fat Shark

2W 5.8GHz 48CH FPV VTX Video Transmitter w/ 0mW/200mW/500mW/1000mW/2000mW + Antenna for Fat Shark

Features:
* Newly upgraded 2W VTX transmitter
* With 5V/500mA output, it can be used with a camera and a flight controller
* Small power ripple
* Input voltage: DC 6-36V
* Various ways to set parameters: Supports for SmartAudio remote control, PWM, and button to adjust parameters
* Weight: 31.3g (without the weight of its antenna)
* Size: 50*25*15.75mm (without the size of the fan)
* Working power: 4 levels can be set, up to 2W continuously
* Working channel: 48CH
* Dual heat sinks and a fan for air cooling
* Good heat dissipation, high power and low current
* Power supply has strong impact resistance
* High-power long-distance VTX: suitable for fixed-wing, racing drones, remote control cars, wireless fishing, etc.

Product Parameters:
* Model: 2W VTX
* Working frequency: 5.8G
* Working channels: 48 channels
* Transmitting power: 0mW/200mW/500mW/1000mW/2000mW
* Working voltage: DC 6-36V
* Working current (12V): 250mA (200mW)/300mA (500mW)/430mA (1W)/530mA (2W)
* Antenna socket: SMA male connector
* Weight: 31.3g (without the weight of its antenna)
* Hole spacing: 30.5*30.5mm
* Size: 50*25*15.75mm (without the size of the fan)

Package Included:
* 1 x VTX transmitter
* 1 x Antenna
* 2 x Cables

Packaging Details:
* Weight: 0.25kg

Attention:
* For high-power (greater than or equal to 1W) single VTX or VTX & camera set, the VTX does not have an anti-reverse connection function. Please connect correctly according to the VTX line sequences, otherwise the VTX and related accessories will be burned out due to reverse connection and users should be responsible for the repair costs. The specific details shall be subject to the manufacturer's test report.
* Be sure to screw on the antenna before powering on the VTX transmitter.

FAQ:
Question 1: What is the transmission distance of the VTX transmitter?
Answer: The transmission distance depends on your receiver, transmitting antenna, receiving antenna, electromagnetic environment and shielding. Therefore, we cannot guarantee the transmission distance of the VTX, but can only guarantee that the VTX is of sufficient power. Other things are not guaranteed.

Question 2: Does the VTX transmitter generate a lot of heat when working?
Answer: The video transmitter transmits signals to the surrounding area like a small radio station, so it will generate heat. The transmitter uses a fan and a heat sink to dissipate heat (the 1.2W version does not have a cooling fan), and the transmitter can work stably for a long time. When using the transmitter, try to place it in a ventilated environment. Under such conditions, there is no problem with the video transmitter working for a long time.

Question 3: Can the antenna of the transmitter be replaced with other antennas?
Answer: Yes. Any antenna that supports 5.8G signals is fine. The 2W antenna interface is SMA male connector. The 1.2 W/1.6W antenna interface is MMCX interface.

Question 4: What aircraft is the transmitter suitable for?
Answer: The transmitter is an independent device. You can install it on anything as long as you want to transmit images and there is a camera receiver. You just need to power the VTX transmitter. You need to fix the transmitter.

Question 5: Does it have camera power supply?
Answer: With 5V/500mA output, the VTX transmitter can drive most FPV cameras.

Question 6: Does the VTX transmitter need to be wired?
Answer: The single VTX transmitter needs to be wired. Please connect the wires according to the wiring sequence in the detailed diagram to avoid wrong connection and burning the transmitter.

Button Configuration of 2W VTX:
After power on, long press the button to adjust the channel frequency point, channel group and power in a loop. Long press the button to switch (red light), short press the button to switch (blue light), and double press the button to switch to Pit Mode (red light/blue light).

Step 1: Long press the button. When the red light flashes once, you can adjust the channel frequency point (1, 2, 3, 4, 5, 6, 7, and 8). At this time, short press the button, and you can switch the channel frequency point. The blue light blinks once to indicate channel frequency point 1, and the blue light blinks several times to indicate the corresponding channel frequency point.

Step 2: Long press the button. When the red light flashes twice, you can adjust the channel group (A, B, C, D, E, and R). At this time, short press the button to switch the channel group. The blue light flashes once to indicate channel group A. The number of blue light flashes increases each time, indicating B, C, D, E and R.

Step 3: Long press the button. When the red light flashes three times, you can adjust the power. Short press the button to switch the power. The blue light flashes once for 200mW, the blue light flashes twice for 500mW, flashes three times for 1W, and flashes four times for 2W.

Step 4: After adjusting the parameters, long press the button. At this time, the red and blue lights will stay on, and the module will enter the parameter saving mode.

Step 5: Short press the button twice to turn on or off the transmission (Pit Mode). The red and blue lights are on, indicating that it is transmitting. The red and blue lights flash (indicating that the VTX is turned off: the module is in Pit Mode). Note: In Pit mode, the working distance of the module is only 1-2 meters.

Note:
1. Screw on the antenna first, then power on the VTX module and use it, otherwise there will be a risk of burning the IC.
2. SmartAudio cannot adjust parameters at the same time as PWM and buttons. After your flight control is powered on again, the default parameters will be written into the VTX again and the parameters set by other methods will be invalid.
3. Please set parameters according to the laws and regulations of the place of use.
4. Remember to leave space for wind flow when installing the VTX to ensure heat dissipation.
5. The maximum current of the module's 5V output power supply is 500mA.

PWM To Adjust Parameters:
PWM pulse width is required to be 1000uS-2000uS. In order to facilitate the operation, it is recommended to use the remote control two-speed toggle switch to set the parameters. The difference between the pulse width of the two PWMs should be greater than 500uS. The pulse width changes from small to large once for effective operation.

A. After powering on, with the dual lights staying on, do two operations within 1.5S (the blue light turns off to on, and the light enters flashing mode), and it will enter the channel setting. When the red light flashes, flip the switch once, and the channel will be added by 1. After flipping the switch, you can not operate it again until the red light flashes, otherwise it will be treated as two operations and it will switch to the next parameter setting. The LED display is consistent with the button parameter setting display.

B. Under channel setting, switch once, the red light stays on and the blue light is off. Switch again within 1.5S (red light on and blue light off to red light blinking), and the blue light will be on to switch to channel group setting. If the red light is blinking, toggle the switch once, and the channel group will be increased by 1. The display is as consistent as the button.

C. Under the group setting, switch it once, the red light stays on and the blue light is off. And the switch is turned on again within 1.5S (the red light is on and the blue light is off until the red light flashes), and the blue light is on to switch to the power setting. When the red light flashes, flip the switch once, and the power will be increased by 1. The display is as consistent as the button.

D. Under the power setting, switch once, and the red light stays on and the blue light is off. Switch once again within 1.5S (the red light is on and the blue light is off to the red light is blinking), the blue light is on and it will exit the setting.

Repeat the above process to set parameters again.