5.8G 600mW 40CH VTX Transmitter + 1500TVL Camera + EWRF 5.8G OTG Receiver for Android Smartphone
Tips:
* It is not a WIFI VTX transmitter. It does not need to be connected to WIFI when in use.
* EWRF classic VTX is designed with 5V output to power the camera. 5.8G analog signal wireless real-time transmission of images. The temperature of 600mw high-power VTX will be relatively high when working. Please place it in a ventilated environment for use. 7-12V is recommended to power the VTX.
* Can be used with all display receiving devices that support 5.8G signals
* 5.8G has weak penetration ability. The transmission distance will be reduced if there are obstacles such as walls.
About the Transmission Distance of VTX:
* The fixed power of the VTX is 600mw. The greater the power, the more stable the VTX. At the same time, the heat generation and power consumption are also greater. These are normal. Pay attention to ventilation and install the VTX without sealing.
* Reference distance of 600mW VTX: The transmission distance of the VTX on a remote control car and remote control boat on the open ground without interference is 50-300 meters.
* The transmission distance of the sky end (model aircraft) without obstruction is 1000-2000 meters. When using mushroom (transmitter) and flat (receiver) antennas, the transmission distance is relatively far.
* The specific distance is subject to actual measurement. The transmission distance is closely related to the environment, and we do not guarantee the transmission distance here.
Aircraft Model Knowledge:
The VTX transmitter has high power, and the more severe the heat, the more stable it is. When working, flickering is normal. When disturbed, the simulated image transmission screen flickers are normal. Please make sure that you don't mind before purchasing. Thank you!
600mW VTX:
Features:
* 5.8G 600mW 40CH digital video transmitter
* With a button for frequency band switching
* With a frequency band display
* With a heat sink for good heat dissipation performance
Specifications:
* Operating frequency: 5.8G
* Operating channels: 40CH
* Transmitting power: 600mW
* Operating voltage: DC 7-24V
* Operating current (12V): 230mA (600mW)
* Antenna: SMA female connector
* Module net weight: 5g
* Volume: 30mm x 20mm x 8mm (excluding the size of the antenna interface)
Button Configuration:
Step 1: Long press the button. Short press the button to adjust the channel group when the digital tube displays letters for the channel group (A, B, C, D and E).
Step 2: Long press the button again. Short press the button to adjust the channel frequency points when the digital tube displays Arabic numeral channel frequency points (1, 2, 3, 4, 5, 6, 7 and 8).
Step 3: After long pressing the button to save the setting parameters, the module will enter the normal working mode (the digital tube will cyclically display the channel group, channel frequency point and frequency).
Step 4 (Pit mode):
* Pit mode: Quickly press the button twice, and the red dot in the lower right corner of the digital tube will be lit. At this time, the VTX is turned off.
* Normal mode: Quickly press the button twice again, and the red dot in the lower right corner of the digital tube will disappear. At this time, the VTX is turned on.
* Note: In Pit mode, the working distance of the module is only about 1-2 meters.
EWRF 5.8G OTG Receiver:
Features:
* 5.8G FPV OTG receiver for smartphones
* Just wire to use it
* Supports AV output to connect to a monitor
* Equipped with 4pin cable
* Power supply has red indicator light, and signal strength is enhanced
* Can be connected to mobile phone/computer
* Supports photo/video recording
* Can be connected to an external display
* Double-button frequency tuning. Simple and easy to operate
* Can transmit sound back [needs support from transmitting segment]
The following conditions must be met to use the UVC receiver:
1: With a phone for Android
2: The phone supports OTG
3: All CPU series for Qualcomm can be supported
4: Kirin 950CPU and higher CPU models
5: MediaTek X20CPU and higher CPU models
6: Not for Apple phones
Attention:
* Please consult customer service if you are not sure whether your phone supports this receiver.
* The antenna with a female connector. BBK phones, OPPO and VIVO need to turn on OTG in the phone settings, otherwise the receiver cannot be connected.
Specifications:
* Weight: 22.8g (receiver with antenna)
* Product size: 56*36*10mm
* Scanning method: fully automatic
* Mobile APP: supports pocket and USB cameras
* Interface: Micro-USB and 1.27mm_4Pin
* Working current: 5V/270mA
* Resolution: 720*480/30Fps
* Connection method: wired connection
* Usage environment: open, unobstructed, and without interference
* Frequency channel: standard 48 channels
* Delay: Micro_USB delay is about 100ms, 1.27_4Pin has no delay, depending on your display performance
Package Included:
* 1 x Set of VTX and Receiver
Packaging Details:
* Weight: 0.3kg
Note:
* Battery is not included.
* Cellphones and the monitor pictured are not included.
SKYZONE SKY02O (Black) FPV Goggles w/ 5.8G Receiver Head Tracker & 640x400 OLED + 3S 2600MAH Battery
$371.79
SKYZONE SKY02O (White) FPV Goggles w/ 5.8G Receiver Head Tracker & 640x400 OLED + 3S 2600MAH Battery
$371.79
SKYZONE SKY02O (Black) FPV Goggles w/ 5.8G Receiver Head Tracker & 640x400 OLED and without Battery
$359.71
