7010+AD9363 SDR Development Board Kit PS/PL Expansion IO Software Defined Radio for PlutoSDR Mini

7010+AD9363 SDR Development Board Kit PS/PL Expansion IO Software Defined Radio for PlutoSDR Mini

Highlights:
- Mini size, compatible with official software
- PS and PL expansion IO, flexible and convenient
- One transmitting and 1 receiving, low cost and lightweight application
- For ZYNQ7010 + AD9363 architecture

Master Chip Parameter:
- Model: XC7Z010-2CLG400I
- Chip level: industrial level
- Recommended max. speed for clock: 628M is recommended for FPGA PLL/MMCM
- PS application processor model: for ZYNQ on-chip hardcore processor, dual-core Cortex-A9, main frequency of 766M
- DDR specification and model: 512MByte, 16bit width, 1066M data rate, MT41K256M16TW-107
- Logical unit (LC): 28K
- Lookup table (LUT): 17600
- DSP unit multiplier: 80pcs
- Trigger (Flip Flops): 35200
- Ram: 2.1Mbit
- Temperature range: -40℃ ~ 85℃
- Speed level: -2

AD9363 Parameter:
- Master chip model: AD9363bbcz
- RF range: 325MHz - 3.8GHz
- Signal data bandwidth: 200K - 20MHz
- Transceiving channels: 2-channel transmitting and 2-channel receiving, IQ modulation (Only using 1 transmitting and 1 receiving for hardware)

RF Part Functional Interface Parameter:
- Antenna interface: SMA female connector
- IQ data sampling rate: USB2.0 interface virtual RNDIS network pot, 5Msps
- Factory firmware driver: for ADI official lib iio (based on official migration for PlutoSDR)
- Clock: 1pcs 40MHz/0.5ppm TCXO
- RF front-end balun: model TCM1-63AX+, bandwidth 10MHz-6.0GHz
- RF LDO linear power supply: wireless LO power supply 1.3V/1.5A power supply 2-channel LDO
- Impedance control: RF front-end to SMA antenna, control 50ohms microstrip line

For PlutoSDR Mini Functional Interfaces:
- Development board power supply: powered through UART serial port, providing 5V input
- Development board clock: 33.33M (PS), 50M (PL), 40M (AD9363)
- USB interface: 1 x USB OTG interface, support USB2.0 virtual network port
- Serial port: 1 x CH340 serial, Type-C, simultaneously used as power supply
- Expansion IO ports: 1 x PS expansion IO port, lead-out SDO/ETHO, 1.8V standard; 1 x PL expansion IO port; 32 x 1.8V single-ended IO
- LED and button: start reset button/DFU upgrade button, USR/PWR/DONE indicators
- Start setting switch: a BOOT dip switch for startup settings
- Onboard FLASH: 32MByte, model MT25QL256ABA1EW9-OSIT
- Debugging interface: 1 x 2.54-6P JTAG pin interface
- Note 1: PL expanding 32 single-ended IOs, which are single-ended wiring and only support the 1.8V single-ended level standard.
- Note 2: The BTB connector of the PL expansion port also includes JTAG signal lead-out.
- Note 3: PS expansion IO allows users to design their own expansion boards to expand SD interfaces and network ports.

Package Included:
- 1 x Development Board
- 2 x Type-C 2.0 Data Cable
- 2 x Acrylic (installed on the development board)
- 1 x Set of Nylon Screws and Stud (installed on the development board)
- 1 x SMA Adapter Cable
- 1 x FM Telescopic Antenna

Precaution:
- Please contact us for development resources after receiving the product.