• Your shopping cart is empty!

  • Navigation Ctroller Kit with ARM9 microcontroller for Mk2.0 Quadcopter

Navigation Ctroller Kit with ARM9 microcontroller for Mk2.0 Quadcopter

Availability: Out Of Stock

  • Price:$122.95
  • Price in reward points: 1230 Reward Points: 12
  • Quantity 3+ units 10+ units 30+ units 50+ units More
    Price /Unit $120.49 $118.03 $114.34 $109.43 Contact US
Quantity:
Buy it now Add cart

You might like

DFRobot 10DOF FlyMaple Self Balance System Flight Control Compatible with Maple Arduino

DFRobot 10DOF FlyMaple Self Balance System Flight Control Compatible with Maple Arduino

$91.48

(0)
LED Light Navigation Lights for FPV Mutlicopter ENZO250 ENZO330 Quadcopter

LED Light Navigation Lights for FPV Mutlicopter ENZO250 ENZO330 Quadcopter

$4.11

(0)
V9.31 Carprog Full Newest Version with All 21 Items Adapters CAR PROG Programmer

V9.31 Carprog Full Newest Version with All 21 Items Adapters CAR PROG Programmer

$74.96

(0)
Pirate Flight Control Board with Atmel 2560 MCU Support MWC MultiWii for Quadcopter Multicopter

Pirate Flight Control Board with Atmel 2560 MCU Support MWC MultiWii for Quadcopter Multicopter

$60.06

(0)
3DR Pixhawk Mini Flight Controller Kit 32 Bit ARM Cortex PX4 for Mini Quadcopter

3DR Pixhawk Mini Flight Controller Kit 32 Bit ARM Cortex PX4 for Mini Quadcopter

$131.90

(0)
MWC MultiWii Standard Flight Control with BEC Connect Board +FTDI Multicopter QuadCopter

MWC MultiWii Standard Flight Control with BEC Connect Board +FTDI Multicopter QuadCopter

$80.33

(0)
KK2.15 Multi-rotor LCD Flight Control Board Atmega644 PA Main Chip for Multicopter No Shell

KK2.15 Multi-rotor LCD Flight Control Board Atmega644 PA Main Chip for Multicopter No Shell

$24.40

(0)
Holybro Flight Controller Drone Flight Controller Pixhawk 6C & PM02 & M8N GPS Module for Quadcopter

Holybro Flight Controller Drone Flight Controller Pixhawk 6C & PM02 & M8N GPS Module for Quadcopter

$295.55

(0)
In together with a MKGPS the navigational capabilities of the Mikrokopter are expanded. (e.g. waypoint navigation, position hold ,...)
The board is already SMD preassembled, there are only a few components left to solder assemble (like connectors, big capacitor).

The NaviCtrl kit is tested and programmed. (including the bootloader)
An update of the firmware is possible via a MKUSB or Sercon.

A MKUSB / SerCon is required for the parameterization / update.

Scope of delivery
  • 1 NaviCtrl (SMD-preassembled)
  • Other components: ribbon cable, crimp connectors for male connector (10pin, 6pin)
  • MKGPS NOT included
  • Option: (2nd 5V regulator) is not included
Hints
  • This is a kit. The SMD parts are pre-assembled, but there are still some parts left to solder for operation.
  • The max. GPS operating radius is approximately 250m around the starting point
  • Only for private, non-commercial use
  • Please note our software license before using

Write a review

Note: We will keep it confidential.
Note: HTML is not translated!
 
Captcha