VAS 5054A Full Chip Version with OKI ODIS UDS for VW AUDI OBD2 Diagnostic with Bluetooth

VAS 5054A Full Chip Version with OKI ODIS UDS for VW AUDI OBD2 Diagnostic with Bluetooth

Description:
The VAS 5054A is a universal diagnostic interface for the vehicles of the Volkswagen Group and all OBD vehicle systems from other manufacturers.
The integrated Bluetooth interface connects the vehicle with a notebook, desktop PC or test system.
No cables are needed for vehicle diagnostics using the VAS 5054A.
The range of the wireless Bluetooth connection is 2 to 5 meters,depending on the environment and the type of Bluetooth adapter used on the PC side.
The Serial Port Profile (SPP) is used for data transfer via Bluetooth. Different Bluetooth security levels are supported.

The vehicle protocols are handled directly in the VAS 5054A.
This ensures fast response times and a reliable real-time behavior independently of the PC operating system. Every time a connection is established, the VAS 5054A software is identified with the version installed on the application PC. The VAS 5054A thus automatically adopts any new features provided after a new software version has been installed on the application PC.
The diagnostic application and the associated Diagnostic Base System are installed on the application PC.
The diagnostic base system can access the VAS 5054A via Bluetooth or USB.

Access via Bluetooth: After a connection to the VAS 5054A has been set up, the Bluetooth software provides a virtual serial COM port (Bluetooth Serial Port Profile). The Diagnostic Base System uses this COM port to communicate with the VAS 5054A.You need to specify this port when you install the diagnostic application.

Access via USB: You can also connect the VAS 5054A to the application PC by using the supplied USB cable. Windows detects the VAS 5054A through Plug and Play, and automatically installs the drivers copied when you installed the diagnostic application. Setup of the VAS 5054A is then complete and the device is ready for use by the diagnostic application.

The Following Vehicle Bus Systems are Supported:
K line (ISO9141-2)
High-speed CAN (ISO 11898-2)
Low-speed CAN (ISO 11898-3)
J1850 (SAE J1850)

ODIS system V3.0.3 Introduction:
ODIS System integrates VW Group's main application system, improves greatly on the efficiency of diagnosis.
ODIS System provide flexible fault diagnosis, clear data test display, convenient diagnosis entrance.
　
ODIS System V3.0.3 Advantages:
* Realizing higher quality and lower cost on repair through high-efficiency diagnosis process!
* The GFF database guided by centralized management posts fault information and solution directly.
* A full range of integration from developing to after sale service makes procedure basis reliable.
* The integration of diagnostic system (eg : Elsa pro) further enhances the core processes of service.
* Systematically optimizes technician’s diagnostic procedure and saves their time cost.
* The optimization of diagnostic procedure makes the distributor’s cost reasonable.

ODIS V3.0.3 System Requirements:
Windows XP / VISTA / 7, both 32bit and 64bit
System C:// have to be NTFS format
C:// need to have at least 20GB space for installing ODIS Software

Functions:
* Diagnostic logs are saved automatically.
* You can choose a dynamic brand layout. This changes then depending on the brand of the vehicle.
* The special functions are represented thematically sortedly.
* You have the possibility to generate a self diagnostic log.
* You can check the connections to backend systems.
* The enforcement of an update was optimized.
* The data-download is carried out in the background.
* An intermittent download is continued automatically.
* You have the option to shut down the system after an update automatically.
* If no online-connection exists, the login-dialog is skipped in the diagnosis entry.
* The Test Instruments view is printed with white background.
* You have the possibility to use a standard mail client to send a support message.
* Certain equipment features can be set, if fitted, manually e.g. national variant.
* There is a mode self diagnostic.
* The self diagnostic can be used also in the case of works with order.
* OBD-functions can be carried out in the self diagnostic.
* Various small optimizations at the graphical user interface.

ODIS Service 3.0.3 Release Note
This release contains software bugfixes

Bugfixes
• VCI exchange not documented in diagnostic protocol
• Internal defects

Release 3.0.3
This release is a new base version with new functions. It has to be installed via SingleSetup.
Reboot after installation
!!! Reboot Windows after installation of ODIS Service!

New functions
• ODIS Service SingleSetup does not install Adobe Reader.
• ODIS Service SingleSetup does not install Virtual Keyboard.
• Support of diagnostic interface VAS6154.
• It is possible to flash an old ECU software version.
• Display of ECU flashability in self-diagnosis is improved.
• The contents of the diagnostic protocol are extended.
• Support requests contain hardware and software version of tester PC.
• Order number is used for diagnostic protocol and diagnostic session filenames.
• Improved manual variant identification.
• Display of names of teststeps can be switched off in GFF..
• Stabilization of GFF hotfix mechanism.
• Diagnostic adresses of ECUs are shown with four digts.
• Improvemed access to self-diagnosis functions.
• New hardware configuration manager for VAS5054/VAS5055.
• Disclaimer changed.
• Changes in ODIS Service update process
• Display of TSB tree without DISS coding.
• Support requests may be stored.
• Display of connection type for diagnostic hardware.
• Support of Internet Explorer 11.

Resolved system defects
• Search in Measured Value Tables did not work correctly.
• Increased occurence of error 4009E
• Some immobilizers could not be adapted.
• Missing timestamp when sending support request in diagnostic protocol

Vehicle restrictions
• For brand AUDI, the Flash mode is supported.
• For brand Volkswagen PKW, the Flash mode is restricted. The usage is only
allowed if described in technical bulletins.
• Flash mode is not supported for all other brands.
• Only immobilizer components are diagnosable in LT2 vehicles.

Supported vehicle models

Supported AUDI-Models
• All AUDI vehicle models are supported.

Supported Volkswagen-Models
• All Volkswagen vehicle models are supported.

Supported Volkswagen Nutzfahrzeuge-Models
• 2K - Caddy 2004 >
• 7H/7J - Transporter 2004 >
• 2C - Caddy 2011 >
• 7E/7F - Transporter 2010 >
• 2H - Amarok 2010 >
• 2E/2F - Crafter 2006-2015 >

Supported Seat-Models
• All Seat vehicle models are supported.

Supported Skoda-Models
• All Skoda vehicle models are supported.

Caution:
* When performing electric welding on a vehicle with an ABS system, disconnect the battery ground cable and the ABS control module connecting cable. The ABS system will be damaged if the ground cable is not disconnected.
* Before disconnect the battery ground cable in vehicles with an anti-theft radio, make sure the security code is available. If the incorrect code is entered when the voltage supply is restored, the unit may be locked even if the correct code is entered later.
* Only use pneumatic or power wrenches to loosen connections or threaded fasteners. Never use these tools to tighten threaded fasteners. This is especially true for light alloys. Always use a torque wrench to tighten to the specifications provided in the repair manual.
* Make sure the ignition is switched off before connecting the vehicle battery. Failing to do this can damage the engine control module.

Package Included:
- 1 x VAS 5054A Unit (Full Chip Version)
- 1 x Bluetooth Adapter
- 1 x USB Cable (Original E256832)
- 2 x DVDs (ODIS Software + English Installation Guide + Video Guide)