Xilinx FPGA USB Development Board Spartan-6 XC6SLX9 + Download Cable Programmer DIY

Xilinx FPGA USB Development Board Spartan-6 XC6SLX9 + Download Cable Programmer DIY

Description:
Xilinx FPGA USB Development board Spartan-6 XC6SLX9:
The easyFPGA-Spartan-6 development board provides a complete hardware environment for designers to accelerate their time to market.The kit delivers a stable platform to develop and test designs targeted to the low-cost and low-power Xilinx Spartan-6 FPGA. The installed Spartan-6 FPGA LX9 device offers a prototyping environment to effectively demonstrate the enhanced benefits of low-cost Xilinx FPGA solutions. Reference designs are included with the kit to exercise standard peripherals on the evaluation board for a quick start to device familiarization.
 
Feature：
- FPGA: Xilinx Spartan-6 XC6SLX9 FPGA
- JTAG Port: On-board JTAG Port for programming
- SDRAM: One 64Mbit Single Data Rate Synchronous Dynamic RAM memory chip
- Flash memory : 32Mbit NOR Flash memory ,Support Byte (8-bits)/Word (16-bits) mode
- PS2 Port: Provides the PS2 port for Mouse and Keyboard
- Pushbutton switches
- User Keys: Normally high; generates one active-low pulse when the switch is pressed
- Infrared Receiver : Communicate with a Remoter for wireless control
- General User Interfaces
  4 User LEDs (Active low)
  4 digit 7-segment displays (Active high)
  Active Type Buzzer
- System Clock inputs : 48MHz oscillator
- VGA output : Uses a 8-bit resistor-network DAC under RGB565 Mode .
- With 15-pin high-density D-sub connector
- AD Circuit and SMA input
- Use an AD chip
- Use a SMA port for AD signal input
- Voltage Regulator Circuit: Provides 1.2V,2.5V and 3.3V for system power supply
- Jumper: Selection for External or on-board AD signal source.
- On-board USB to TTL/RS232 Module
- Use PL2303 for USB-TTL/RS232 Converting (Without DB-9 serial connector)
- 26-PIN Expansion Headers
- Spartan-6 I/O pins, as well as 3 power and ground lines, are brought out to the 26-pin expansion connectors
 
Xilinx USB Download Cable Programmer:
Features:
- Support all Xilinx devices:
- All Virtex FPGA families
- All Spartan FPGA families
- XC9500/XC9500XL/XC9500XV CPLDs
- CoolRunner XPLA3/ CoolRunner-II CPLDs
- XC 18V00 ISP PROMs
- XCF00S/XCF00P Platform Flash PROMs
- XC4000 series FPGAs

- Supported on Windows and Red Hat Enterprise Linux
- Work with impact , chipscope pro and microblaze embedded processer debuging
- Support target system using 5.0V TTL,3.3V LVTTL/LVCMOS, 2.5V, 1.8V,1.5V
- Apply to Xilinx CPLD / FPGA chips download debugging.
- Support JTAG, Slave Serial, SPI download mode, can configure all Xilinx devices.
- Xilinx Platform with USB Cable fully compatible.
- Target device to download the clock options, up to 24MHz.
- Support iMPACT and ChipScope.
- Firmware can be updated automatically.
 
Package Included:
- 1 x FPGA Spartan-6 XC6SLX9 board
- 1 x Xilinx download cable set
- 1 x Remote controller
- 1 x USB Cable
- 1 x CD (Sch, example code, IC datasheet)